Setup guide rectangle for Aeros models
Here you will find a basic guide on how to assemble our round shower double sliding door shower series. NOTE: this is for frame assembly only, assembly of parts and accessories can be found on their respective model page…
Setup guide for Aeros rectangle double door models.
Setup guide assembly procedure for rectangle shower frame and base
Step 1
Rectangle double sliding door shower model.
Available in 1 size and is designed to stand in against a wall or a corner.
1200*900*2090 ~ 2290 mm
Step 2
Rectangle shower tray assembly.
Level the shower tray feet below the base and connect it to your waste pipe.
Step 3
Attach all the fittings to the rear panel according to the model you purchased.
Connect hoses from your water mains to the shower mixer and test that all hoses and connections are tight and sealed from leaks.
- Lower the middle panel over the aluminum rail on the base.
- Insert a grey wedge between the rail on the base, and aluminum on the frame.
- Insert the 2nd grey wedge on the other side of the middle panel.
Step 4
NOTE: Attach any accessories to the left rear wall according to your model prior to attaching to the middle panel.
Attaching and securing the left rear panels.
- Interlock the middle panel and rear wall, and ensure the panels are locked in completely from top to bottom.
- Rotate the left rear wall until both middle and rear walls form a straight line.
- As you are rotating the left rear wall, the bottom of the wall should slide and insert into the aluminum rail on the base.
The rear wall should now be locked with the middle panel and the shower tray.
Step 5
The right rear wall is attached in the same manner as the left rear wall, following the same steps.
NOTE: Attach any accessories to the right rear wall according to your model prior to attaching them to the middle panel.
Step 6
The last step to securing the rear panels is to lock them together using the right-angle aluminium rail.
- Lower the aluminium rail so the angle slides between the aluminium of the middle and rear panels.
- Insert plastic grey wedges so they slide between the aluminium rail and the top of the frame of the rear wall.
- Slide until grey wedges are completely inserted and locked in position.
Step 7
To attach the side wall you first need to place the bottom door rail at the front of the shower base so that when you lock the side wall it should slide over the block.
With the front door rail on the shower base, lock the side wall to the rear panel.
Rotate the side wall outwards until it fully locks into place.
Raise the side wall enough to allow the side wall to slide the cut out of the side wall to insert over the block of the door rail as shown.
Step 8
To attach the other side wall, insert the wall at an angle until it is fully into the rear wall.
Rotate the side wall until it locks in at a right angle.
Raise the side wall enough to allow the door rail to insert into the slot of the side wall and slide down until the door rail is fully inserted into the side wall, as shown.
Step 9
The last step is to attach the top rail.
Insert the door rail blocks into the slots of both the side walls and lower them simultaneously into the side walls until fully inserted.
NOTE: you may need to tap the top door rail down with a rubber mallet as it will be new it may be tight.
Step 10
Attach the door handles to both of the doors, the wide side will be on the inside, and the narrow side will be outside.
Step 11
When attaching wheels on the door check that you have the top of the door in relation to your door entry.
Check by matching the magnetic strip on the door will match the magnetic strip on the side wall.
Top wheels are your level adjustment wheels, screwing the knurled nut will either raise or lower the door depending on what way you turn the nut.
The grub screw will lock the wheels from coming loose over time.
The bottom wheels are spring-loaded to insert into the bottom door rail.
NOTE: When screwing wheels into the door frame, we suggest using Loctite to ensure the bolts do not come loose over time.
Step 12
Once wheels are attached to the doors it is time to raise the doors and attach them to the shower.
Starting with one door, maneuver the door inside the shower, and raise the door so one of the top wheels sits on the lip of the door rail and the other wheel sits on the lip of the side wall.
As the door hangs off the top wheels, reach down and pull the springs down on the bottom wheels and insert them into the bottom door rail and the bottom side wall rail.
Check the door slides smoothly, it’s not rubbing on the frame and the bottom wheels are not popping out of the rails.
If so you need to adjust the top wheels by turning the knurled nut and leveling the door accordingly.
Step 13
OPTIONAL
Cut any excess aluminum profile from wall mounts if they are to be used.
Attaching the wall mounts.
You have a few options depending on what type of wall you are securing the wall mounts to.
You can use screws and dowels to secure any type of wall, plaster, tiles, concrete, or brick or you can use liquid nails to secure the wall mounts.
To secure the wall mounts to the shower you can screw them into the frame, no glass is present at the position where the wall mounts are attached.
NOTE: Wall mounts are optional, the shower can stand on its own and not move over time due to its weight. Wall mounts will stabilize the shower from any movement.
Step 14
If you are to use the screws and dowels provided.
Mark the hole positions of the wall profile onto the wall on either one or both sides of the shower.
If the shower is placed in a corner, only attach the side where the wall mount can be attached.
One wall mount is enough to stabilize the shower!
Step 15
Using a drill and a 5.5mm drill bit.
Drill holes where you marked the holes.
Insert the dowels into the holes
Step 16
Place the wall mount into position.
Insert the screw through the cap washer and screw it into the dowel.
Once all screws have been inserted use the cover caps to give you a clean finish.
If you have any questions or require assistance regarding the setup guide for Aeros rectangle models leave a comment below or use our customer service form from this link
Add comment
You must be logged in to post a comment.